Friday, 6 February 2015


hii guys today we are going to work with "DTMF BASED MOBILE OPERATED ROBOT"
its easy diy
OVERVIEW
In this project "Cell Phone Operated Land Rover", the robot is controlled by a mobile phone that makes a call to the mobile phone attached to the robot. In the course of a call, if any button is pressed, a tone corresponding to the button pressed is heard at the other end of the call. This tone is called DTMF (dual-tone-multiple-frequency).The robot perceives this DTMF tone with the help of the phone stacked in the robot. The received tone is processed by the (ATmega8) microcontroller with then help of DTMF decoderMT887o. The decoder decodes the DTMF tone into its equivalent binary digit and this binary number is sent to the microcontroller. The microcontroller is programmed to take a decision for any given input and outputs its decision to motor drivers in order to drive the motors in forward direction or backward direction or turn. The mobile phone that makes a call to mobile phone stacked in the robot act as a remote. so this robotic project  is not require the construction of receiver and transmitter units.


CODE:
I have written code in programmers notepad for WINAVR software..it is easy to understand..
here is the code..
//by praveen winrap

#include<avr/io.h>

#include<util/delay.h>

int main(void)

{

DDRD=0xff;

DDRB=0×00;

while(1)
{
if((PINB & 0b00000010)==(0x02))
 {
  PORTD=0XA0;
 }
else if((PINB & 0b00001000)==(0x08))
  {
  PORTD=0X50;
  }
else if((PINB & 0b00000100)==(0x04))
  {
  PORTD=0X40;
  }
else if((PINB & 0b00000110)==(0x06))
   {
    PORTD=0X20;
   }
else
    {
     PORTD=0X00;
     }
}
}


CIRCUIT DIAGRAM:


INDIVIDUAL COMPONENTS:
1.ATMEGA8L MICROCONTROLLER


2.DTMF DECODER:

L293D MOTOR DRIVER:


here some of pics of bot..
s







APPLICATIONS:
1.AGRICULTURE SIDE

2.CONTROLLING HOME APPLIANCES wireless...

Comments

Post a Comment

Popular posts from this blog

Flashing WINAVR code to Microcontroller using ARDUINO Bootloader

Image
                             Hey all...after a long time i came with a new idea which i have implemented,it is programming a AVR micro controller using WINAVR with ARDUINO as Programmer.its little bit confusing,dont worry.I will give you complete description.                                                                  Generally we program a micro controller using a programmer,so here it is normal programming.normal programming in sense??we use the programmer according to the software we used(for example,to program arduino we use a usb cable which  connected between pc and FTDI circuit as a programmer here controller will accepts the code because it contains a boot-loader ,similarly in AVR controllers we use some isp programmers like seria...
Read more

RF REMOTE..

Image
Want to make everything wireless..??? Huh.!! Then u r at right place. There are many wireless technologies like ir,DTMF,rf etc of these IR and DTMF are covered in earlier posts. So now its time for radio frequency communication.. Dont be get puzzled In this post I will direct you how make simple RF remote.. So for making remote,components that you required are *HT121D *HT121E *RX TX MODULES *1.1M ohm resistor *55k ohm resistor Now its time to know about encoders and decoders.encoders is a thing which creates some data at transmitter end. Decode is opposite for those encoders it simply decode the data which has been transmitted by encoders..so from this we conclude that encoders should always lies at transmitting section and decoders lie at receiver section MAKING A TRANSMITTER: MAKING A RECEIVER: This is how rf MODULES looks
Read more